Pressure Activated Re-circulator
PN:
67000
Click Here to Download
Product Information and Instruction Guide - PDF version
CLICK "ADD" BELOW TO ORDER ONLINE
Pressure
Activated Re-circulator
PN:
67000
$137.00
USD
Click Here to Download Our Current Price
Guide - PDF version
|
This Pressure Activated Re-Circulator
is a must have if the products you are spraying need to be continuously
circulated. It can be installed in minutes and is easily adjustable.
Simply adjust the pressure setting from 50 to 175 PSI and the
re-circulator will automatically open.
Features
- Easy to install on your current
power sprayer.
- Can be turned on or off and is
easily adjustable.
- Durable all brass construction.
WARNINGS
- BEFORE USE - ALWAYS CHECK FOR LOOSE
HOSE CONNECTIONS.
- BEFORE USE - ALWAYS CHECK THAT THE
RE-CIRCULATION HOSE WILL OCCUR.
- DO NOT USE ON CLOSED CONTAINERS
WITHOUT ADEQUATE VENTING.
- DO NOT USE A RE-CIRCULATOR THAT IS
DAMAGED OR MALFUNCTIONING.
Instructions
Installation Instructions
- The re-circulator comes fully
assembled and includes two (2) 5/8" hose clamps for installation.
Step
1 - Choose Location
- To install the re-circulator,
identify the output side of your power sprayer.
- Recommended Locations:
- RP - Between the pump cover and
the base of the reel on the 3/8" yellow hose.
- SP - Where the 3/8" yellow hose
comes out of the pump cover.
Step
2 - Cut
- Cut the hose in a location that
will allow the easy installation of the re-circulator and the two (2)
5/8" hose clamps.
Step
3 - Install
- On the hose section that was just
cut, slide one (1) over each cut end and insert the 3/8" hose barbs on
the tee into the cut end sections of the hose (fig 1)
Step
4 - Tighten
- Securely tighten the hose clamps
over the hose and the hose barbs. Check these connections prior to
every operation.
Operation Instructions
- Once installed, the re-circulator
can easily be adjusted between 50 and 175 PSI. These settings are
clearly marked on the knurled knob.
Step
1 - Adjust and Secure
- Simply twist the knob
counter-clockwise to the 50 PSI mark and secure the
re-circulation hose into the container from which you will be spraying.
Step
2 - Turn on Sprayer
- Power on your sprayer and prime as
normal.
- When the sprayer is fully primed,
release the shut off handle and the power
sprayer will build up enough pressure to activate the bypass valve.
- Product should now be flowing
through the clear re-circulation hose back into
the container.
Step
3 - Adjust
- When spraying high solids or high
viscosity products, the re-circulator may need to be adjusted to a
higher PSI to prevent the re-circulator from activating while spraying.
- This is done by rotating the
knurled knob clockwise. Only adjust pressure slightly higher than
necessary to prevent activation during spraying applications (See fig
2).
 - To turn the re-circulator "OFF",
simply rotate the knurled knob clockwise to the 175 PSI mark or as far
as the knob will
rotate.
- If your sprayer generates more
than 175 PSI of pressure you may need to install a ball type shut off
valve on the clear re-circulation hose to prevent circulation. This is
not necessary for REAL Pump and Spray 'N' Pail products
Step
4 - Clean
- When finished spraying, be sure to
allow some of the cleaning solution being used to clean the sprayer to
pass through the re-circulator.
- Failure to clean the re-circulator
properly may cause the valve to stick rendering the re-circulator
non-operational.
If you have any questions regarding the operation of this product
please feel free to contact Customer Support by
telephone: 800.801.7832 – 847.639.7272 or via email:
support@4progressive.com.
REV110508
|
|
|
|
|
|
